No LED lights turn on when pushing keyboard keys or moving mouse even when pc is off. This is good, it means the processor is functioning and the motherboard is good so far. More beeping: "no video card" beep code. One is an old AMD CPU. You should get a beep code that tells you there is no memory. Hey guys. My monitor looks fine. The POST is the computer's way of checking the necessary system requirements and hardware connections for the system to power up properly. Now the first thing you’ll need to make sure about your monitor is, that it’s ‘Powered ON’ and the video cable is connected properly.Most of the times just because of some loose cable, a lot of people having this black blank display related problem. When the error occurs, the corresponding LED stays lit until the problem is solved. So I just built my first PC a couple of days ago and everything was running fine with no issues. If your CPU is compatible, please make sure the CPU power connector has been well attached. DRAM-LED lit on: The RAM or CPU is not detected or fail or be incompatible with the motherboard. VGA-LED lit on: the graphics card or the CPU with integrated graphics is not detected or fail, BOOT-LED lit on: Indicates the booting device is not detected or fail. Type in your model on the top right corner’s search bar of MSI official website, hit [Enter] to find the matching result. After firing up all fans and lights work except for GPU fans. Next, verify the monitor has power by looking for a blue, green, or orange light. Almost 50 percent of the time, if no beep and no display are observed, this is indicative of a dead motherboard. When pressing the power button to power up the computer, the fan and LED indicators perform normally, but nothing gets displayed on monitor at all, please follow the instructions below to troubleshoot: To check if your CPU is compatible with the motherboard, please refer to the compatibility report on MSI.com. Actually, i'm trying to get a config that works perfectly, just try and failure, modifying some options... Well, let's see what happens :S. Hey, I have experienced the same nonsense with that board as well. If you see no lights on the monitor, make sure it is connected to a working wall outlet. have you tried removing your gpu and making sure it has the correct power cable attachments from the PSU (4pin, 6pin, etc) ? The CPU fan even spins. 0 0. Then I put the CPU back in, put the cable for power for the motherboard into the PSU, then put the CPU power cable into the PSU, and plugged that into MB, and then I turned it on. 3. I have a gigabyte aorus pro wifi board with amd ryzen 3700x. The DRAM light can be 3 things which is not helpful. They are all normal motherboards. My PC will turn on, the fans will spin and all but there is no picture going to the monitor.. Motherboard stuck on white VGA light: Question New Build. All. When you press the power button to turn on the computer but there is no display on the monitor, please follow the below steps to troubleshoot : 1. Any ideas? I can confirm that the PSU was not the problem. I know this topic has been stated before, but there are no threads that explain the step by step workflow to discovering the cause of the problem. After 2 months of using my first ever built PC with no issues, I could really appreciate some help figuring out this new hardware issue. This should be our goal. 5. But still computer is not booting up and nothing on monitor. Check the power supply. But the CPUS are different. The most common way that a computer "won't turn on" is when the PC actually does power on but doesn't display anything on the monitor. The probIem: In my case: my Inspiron 620 desktop won't turn on, no light on button, solid orange or amber if you prefer, on board. Regards, Start with a build as light as possible - no storage, one stick of RAM, CPU, GPU and see if you can get into BIOS. The plug snaps in the socket this time.) Note: For the Intel platform, please check your external monitor, cables or graphics card, if you have a spare one, try cross-testing with them to confirm the issue. The PC turns on. There is no display with the GPU installed or uninstalled. I have a new lead but I'll respond to your individual points first. Three days later in the middle of me using it the display cut out and I got the Yellow Led on my motherboard indication an issue with my DRAM. MOBO constantly has red DRAM light on on power up no POST and no beeping sounds. if not give display in both case then check your motherboard with the help of component eng. Disconnect the main AC power by either shutting off the power button on the back of your power supply or simply pulling out the power cable. I'm kicking at myself because I knew it so well. i3 8350k 8gb ram 3000mhz, auraflow 120 Thank you in advance. What do you think could be the cause of this? Tags: NoDisplay. But there is no display. I can confirm that the PSU was not the problem. If yes, please try another CPU. But no display. The diagnostic lights are not lit after the computer successfully boots to the operating system but there is no display showing. Motherboard's Debug LED indicates failure with CPU. Cpu Overheating is unlikely as it would cool down considerably faster than 8 hrs. You need to make sure the actual model is of a good quality. When pressing the power button to power up the computer, the fan and LED indicators perform normally, but nothing gets displayed on monitor at all, please follow the instructions below to troubleshoot: Check CPU compatibility; Check CPU power connector is in position; Perform a POST test; Reset BIOS; Check EZ Debug LED indicator; Check CPU compatibility Select [Compatibility] down below the model name. Check the memory. 6. I don't know about the others I have. © Valve Corporation. When I disconnected my monitor from the CPU, I get a test message as no signal. Re-install the CPU. ONe is an Intel Pentium 4. Check the monitor. Upcoming No whir, no fan. You can also remove the CMOS battery for about five minutes from your motherboard. Also, I tried booting with 1 stick of RAM and with 0 sticks of RAM. Was using my pc then suddenly it just froze so I turned it off by holding the power button. Note: This is ONLY to be used to report spam, advertising, and problematic (harassment, fighting, or rude) posts. even though on z370 everything was fine. Page 1 of 3 - PC does not boot, no (post beep, light, or display ) fans running - posted in Internal Hardware: When I boot my pc, all fans are running, no post beep, no pc display. Reseat the CPU, Clear the BIOS and update the BIOS. ... Windows 7, 4Gigs of ram. Even the GPU fan. "No display" can also mean no lights (LED) on the motherboard or no video is being displayed to the monitor. You see lights on the computer case, probably hear fans running from inside, and may even hear sounds, but nothing at all shows up on your screen. 2. Unfortunately, when I switched on my machine, my display didn't come up. If that doesn't solve it you probably have a defective motherboard. Make sure you use the right memory banks on the board (shown in manual) and if you have the option of using different banks, try that too. Clear the BIOS data by moving JBAT1 from its original 1-2 position to 2-3 position after discharge the computer. CPU as it holds the memory controller, motherboard or the RAM.